Model 1 Sales 300 whisper upper function problems

[jripper]

No, I have not chronograph that load. I will probably do that this week. I believe I was using federal small rifle primers (standard, not magnum).
It burns every bit of powder, and I don't think a magnum primer is going to make much difference.

Right now, I have been going by sound and feel, and it would appear to be subsonic, but I'll Chrono to check.

I don't know about the rest of you, but I am seeing a lot of variation from listed loads, vs. what I am getting from my own gun.

I have also seen a lot of variance on what different people are calling a maximum load.

For instance, I am using 18.5 grains W296 behind a 125 rem. psp. Some people list a max load of over 21 grains. Past 18.5, I am blowing primers out of the cases!!!

I guess that it what can happen when working with a semi-wildcat.

Joel

[sharpshooter33]

Ok I've been tinkering with my 300/221 for awhile now. I have a load that duplicates the Corbon 220 Subsonics on paper, but does function my action. I'm using 11.0 gr of AA-1680. With my setup cases/primer/seat depth etc... I'm getting the same sight settings on the Corbon 220subsonics as I am with my 220gr subsonic reloads. The difference is mine cycle the action.

My AR cycled fine with lockouts on my last round. My problem and question is....That it failed to extract on several cases. I've examined the extractor and it looks fine. Unknown if the spring is strong enough or not though. The second possibility could be that the action is trying to pull the casing out before the pressure has went down (or the bullet has left the barrel)

Has anyone else experienced this problem?

I'm shooting a 300/221 M1S 16" barrel, CAR length AGT full open and with full size stock and buffer setup. Is there any signs that I can look for to indicate which it may be?

I'm going to replace the extractor spring 1st then if that doesn't work I'm going to be clueless.

I did notice that I could hear the bullet impact at 100yards and also on the recoil I could see the bullet right before it struck the target at 100yrds. That was funny. I was using the Corbons and single feeding them. I even let a friend watch it through the scope on a couple of rounds. It didn't leave oblong holes. The bullet was stabalizing. I don't have a Chrono, but I would say they are in the 850-1000fps range.

Anybody have any input I would appreciate some thoughts on this one

[rednek58]

I know two things that might help you with the failure to extract. D-Fender brand ring that fits around the extractor spring, also a heavy Wolff extractor should help. Either one alone might work, but I have used them together with good results. Hope this helps.

[sharpshooter33]

Ok, I've fixed my extractor problem. I now have a fully functional 300/221 fireball from Model 1! I'm using Jrippers load of AA1680 at 11.0gr and 220gr SMK's sized alittle longer than Corbon's, but they still fall below 2.260 OCL. I've used RP and LC cases and both are just fine. This load seems to be shooting somewhere around 950fps.

I'm a happy camper! Now I just have to get a suppressor and my project will be complete.

BTW when I put it back together I ordered a MRFS-C and drilled a hole for my AGT. It is a bad ass looking setup right now. Will be even nicer when I get it suppressed.

I see a 300/221 bolt gun in the future also. I'd like a real quiet one. 8-)

Thanks for all the input here guys. I would never known I had a problem unless I was reading these posts and I wouldn't have known how to fix it either.

Thanks
SS33

[jripper]

Glad to here your upper is running well. Mine is also, altough a few weeks ago, a friend came over, and we went to try it out, and I got failure to feed/extract short stroking again, sub sonic or super sonic. When I pulled ou t my bolt, I found that the carrier key had come loose. I then noticed that the "staking" on the model 1 bolt did not even touch the allen screws. I put red loc tite on them, and staked them a little deeper, and it all works again.

Just something to check if you are using a model 1.

Thanks everyone here for their help, as I don't think I could have gotten it going without the input here

Joel

[jripper]

I finally chronographed my 11.0 AA 1680 and 220 sierra load. Out of my 16" M1S ar, 3 shots averages 980, with a high of 1020 and a low of 933.

Only did three, as that was all I had on hand, and it was starting to rain.

Joel