Quarterbore.Net Forums

Go Back   Quarterbore's Forums > Search Forums
Reload this Page Search Results
Home Forums Classifieds Photo Server FAQ Members List Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 14 of 14
Search took 0.01 seconds. Search: Posts Made By: rv10flyer
Forum: 300 Whisper Rifles and Pistols 10-03-2011, 11:34 PM
Replies: 4
Views: 1,143
Posted By rv10flyer
Good info, thank you.

Good info, thank you.
Forum: 300 Whisper Rifles and Pistols 10-03-2011, 08:49 PM
Replies: 4
Views: 1,143
Posted By rv10flyer
I shoot AR500 targets at 100 yards without a...

I shoot AR500 targets at 100 yards without a problem, but I'm not sure about T1 though. It might make a nice round hole. :eek:
Forum: 300 Whisper Rifles and Pistols 09-13-2011, 10:49 PM
Replies: 30
Views: 5,025
Posted By rv10flyer
Wow :eek:, glad you are OK.

Wow :eek:, glad you are OK.
Forum: 300 Whisper Rifles and Pistols 04-09-2011, 01:01 PM
Replies: 12
Views: 2,768
Posted By rv10flyer
Yes, make sure your loads are stable before...

Yes, make sure your loads are stable before attaching the suppressor. I normally test my loads under a chrony with the target at 20 yards or so. Once I am happy I then test at 50 and 100 yards. If...
Forum: 300 Whisper Ammo and Reloading 02-20-2011, 05:01 PM
Replies: 9
Views: 2,917
Posted By rv10flyer
I wanted to update this post with a few data...

I wanted to update this post with a few data points I have collected so far. I am shooting an AR-15 with a 10.5” carbon barrel from Paladin, 1x8 twist, 3-way gas block, AAC 762-SD (not used during...
Forum: 300 Whisper Rifles and Pistols 01-08-2011, 02:00 PM
Replies: 23
Views: 3,974
Posted By rv10flyer
:welcome: to the club. I would recommend...

:welcome: to the club.

I would recommend getting the case gage along with your barrel from tp555/Paladin. This will make reloading easier. Also, you will need a shorter gas tube with the...
Forum: 300 Whisper Ammo and Reloading 12-13-2010, 09:43 PM
Replies: 9
Views: 2,917
Posted By rv10flyer
Thanks for the responses. What C.O.L. are you...

Thanks for the responses. What C.O.L. are you seating the projectiles to? The 208’s I measured are about .020 longer than the SMK 220’s. I’m more limited by the magazine than some of you running...
Forum: 300 Whisper Ammo and Reloading 12-12-2010, 07:57 PM
Replies: 9
Views: 2,917
Posted By rv10flyer
208 AMAX and VV N110 Load Data?

Does anyone have any 300 "Whisper" load data utilizing the 208 grain AMAX and VV N110 that they would be willing to share?

Thanks in advance.
Forum: 300 Whisper Ammo and Reloading 06-02-2010, 11:00 PM
Replies: 37
Views: 7,432
Posted By rv10flyer
What load are you using for the 208's and out of...

What load are you using for the 208's and out of what hardware (barrel length, twist, AR/bolt, ect.)? Thanks!
Forum: 300 Whisper Ammo and Reloading 05-30-2010, 07:49 PM
Replies: 4
Views: 1,312
Posted By rv10flyer
Send me a PM with your email address and I will...

Send me a PM with your email address and I will send you the load data from the Sierra manual (I tried to upload the pdf here but it is too big; only 85 KB). It has data for both the 220 and 240...
Forum: 300 Whisper Rifles and Pistols 05-16-2010, 02:10 PM
Replies: 30
Views: 7,127
Posted By rv10flyer
I have been very pleased with my barrel and 3-way...

I have been very pleased with my barrel and 3-way gas block. I’m still working up loads so I don’t know the ultimate accuracy potential but I am happy with the results so far.

His response to...
Forum: 300 Whisper Ammo and Reloading 02-19-2010, 11:15 PM
Replies: 6
Views: 1,702
Posted By rv10flyer
Thanks

I used a flathead screwdriver to spread out the two thread halves. This increased the overall length to about 1.360. With a little additional effort I then screwed the case length gage in more and...
Forum: 300 Whisper Rifles and Pistols 01-28-2010, 10:18 PM
Replies: 27
Views: 6,988
Posted By rv10flyer
Yesterday their website said they were out of...

Yesterday their website said they were out of stock but today it says in stock again.
Forum: 300 Whisper Ammo and Reloading 12-02-2009, 06:13 PM
Replies: 6
Views: 1,702
Posted By rv10flyer
Lee Case Trimmer / 1.345?

I am using a Lee manual case trimmer to trim down Lake City brass after running them through a Redding full length sizing die. They are coming out to 1.345 instead of 1.355. Will this slightly...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -4. The time now is 03:07 AM.
Contact Us - Quarterbore's Forums - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.