Quarterbore.Net Forums


Go Back   Quarterbore's Forums > Title 1 Weapons Forums > Other Rifle Topics
Home Forums Classifieds Photo Server FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 03-05-2011, 06:22 PM
WhisperFan's Avatar
WhisperFan WhisperFan is offline
Member
 
Join Date: Dec 2006
Posts: 86
Remington 700 feeding - Photos added !!!

I have a problem I hope someone else can help with.

I took a Remington 700 in .223 and did a rebarrel on it. I put on a Remington factory 700 bull barrel in .308 - I had to replace the magazine box, the follower and mag spring (for .308)
I also bought a bolt - I don't think the bolt is the problem.

So - now the barrel is mounted, it had been properly headspaced, and I had it reblued. Everything is as it should be .... except it wont feed - at all.

When the cartridge is on the 'outside' (nearest the ejection port opening) the bolt pushes the round forward about 1/8" and as the bullet nose starts up the feed ramp, the back end drops and the bolt face goes over the back of the round and pushes the round down into the mag.

On the 'inside' it's not much better. The bolt will push the round forward, and when the bolt jumps the rim of the cartridge, if I pull back on the bolt handle and then push forward again, I can sometimes get it to feed. But that doesn't happen on the 'outside'

Was the .223 receiver different than a .308 short action receiver in any way? I'm thinking the feed ramp area - or the 'lips' at the top of the box magazine?

I even took the rifle out of the stock and assembled it without the stock and it does the same thing.

Thanks in advance

Last edited by WhisperFan; 03-06-2011 at 07:08 PM.
Reply With Quote
  #2  
Old 03-05-2011, 07:28 PM
HUNTER2 HUNTER2 is offline
Senior Member
 
Join Date: Dec 2008
Posts: 231
What does the nose profile of your bullets look like? OAL length too long? !!

Last edited by HUNTER2; 03-06-2011 at 01:07 AM. Reason: wrong answer...
Reply With Quote
  #3  
Old 03-05-2011, 11:26 PM
WhisperFan's Avatar
WhisperFan WhisperFan is offline
Member
 
Join Date: Dec 2006
Posts: 86
I'm using 7.62 nato and Winchester factory.

Neither one works!
Reply With Quote
  #4  
Old 03-06-2011, 07:08 PM
WhisperFan's Avatar
WhisperFan WhisperFan is offline
Member
 
Join Date: Dec 2006
Posts: 86
Single round on the ejection port side.


How much the bolt has to push on


2 rounds loaded


How much the bolt has to push on


Parts


Parts


Parts


Receiver from the bottom


Between the feed lips is .537"


.374" from the outside of the receiver to the inside of the feed lip on the ejection port side


.436" from the outside of the receiver to the inside of the feed lip on the non-ejection port side



I hope someone can take some photos and we can compare to a .308 receiver.
Thanks
Reply With Quote
  #5  
Old 03-07-2011, 08:21 PM
WhisperFan's Avatar
WhisperFan WhisperFan is offline
Member
 
Join Date: Dec 2006
Posts: 86
Got it -
I went to my local gun shop and took some measurements off a used 700 he had in .308

The feed lips on a stock .308 are beveled the full length, where as mine were not.

Got what I needed, beveled mine, and function tested it. Works 100%
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:22 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.