Quarterbore.Net Forums

KillJoy149 · #1 09-12-2005, 01:15 PM

Where is everyone getting their Flats from?

Do they still have the Front and Rear Trunnion Holes drilled?

KillJoy

Quarterbore · #2 09-13-2005, 11:02 AM

I am building one now with a flat I got from ak-builder.com. This new flat does not have all the trunion holes (It does have one at the rear) and the receiver really looks nice so far. This is the flat that I am bending for the site and shown in the photos in the link above.

KillJoy149 · #3 09-13-2005, 03:31 PM

I was just wondering.

I just picked up five from Cope's Distrubiting for $11.99 each, that do have the Front and Rear Holes (according to the guy there who answered the phone) and rails.

I got them from them because Tapco no longer had any with hole listed on their Website, but they are now listed today. Oh well. Hopefully I will get a decent quality product.

Now I am in need of a good source for Rivets.....preferrably on the cheap :)

KillJoy

Quarterbore · #4 09-13-2005, 03:53 PM

I split this off the jig rental thread...

I find it interesting that you are looking for flats with the holes when most guys are after flats without them... My first flat seemed to lign up with my trunions fine (AMD-65 build) but I know others had to egg out holes and JB weld to make them look better.

I am quite impressed with the flat that I got from AK-Builder.com although there are a couple strange holes on the bottom of the receiver that I don't quite understand... I really need to get my phtos cropped down and posted however to show them but they are rear of the pistol grip and they are wide like the front rivets for the trigger guard. They will not hurt anything and I can hide them so no biggie...

Just the same, both these new ones and the original Tapco flats seem to bend the same so either will work as will others!

KillJoy149 · #5 09-13-2005, 04:09 PM

They are probably for the Receiver Stiffener used on Folding Stock Rifles. It mounts inder the Pistol Grip.

KillJoy

KillJoy149 · #6 09-13-2005, 04:11 PM

Also, I like the ones w/ the holes because there is less guess work involved. My Polish Underfolder turned fixed stock lines up perfectly w/ the Tapco's.....

KillJoy

Quarterbore · #7 09-16-2005, 11:12 AM

Yea, I never had problems with the holes being off a great deal but that depends on your kit. I just received a new flat from AK-Builder.com and it is the polish underfolder flat. I hope to get that bent up soon so I can post feedback. From first looks it is a nice looking flat.

KillJoy149 · #8 09-16-2005, 12:08 PM

You're much more brave than I.

Whenever I only get one of something, it is doomed to be a failure!

That's why I got 5 this time around. Hopefully, at least one will turn out well.

KillJoy

Quarterbore · #9 09-16-2005, 04:49 PM

I just figured out the flats I am building on now are not from AK builder but instead from:

http://www.MidwestArmory.com

These are no trunion rivet hole flats and they are the ones I have pics of in the jig rental thread... I really need to get the pics and directions up for the jig usage!

Th eLA power outage caused a numbe of my websites to go down and I have a couple sites that have some pretty major problems that i have been trying to fix when I am not at work or playing with gun stuff... Too many hobbies is not a good thing I guess!

555th · #10 09-16-2005, 10:36 PM

Quote:

Originally Posted by KillJoy149

They are probably for the Receiver Stiffener used on Folding Stock Rifles. It mounts inder the Pistol Grip.

KillJoy

The underfolder plate is spot welded in on factory AKs, so no holes should be aloud..I bet it is an alignment hole of some sort to index the laser cutter to the rest of the flat and it is hidden by the PG. It really doesn't matter much, if you are building an UF it will be covered by the reinforcing plate or at least be covered by the PG if it's a standard stock build.