Quarterbore's Forums - Search Results

		Quarterbore's Forums > Search Forums
Search Results

Showing results 1 to 9 of 9
Search took 0.01 seconds. Search: Posts Made By: redneckdan

Forum: 300 Whisper Ammo and Reloading

01-14-2008, 03:23 PM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

castboolits has regular group buys, lee is kinda...

castboolits has regular group buys, lee is kinda back logged right now. cost is usually $60-ish for 6 cavity moulds. The problem is overal length limits. They mass produce mould blocks and don't...

Forum: 300 Whisper Ammo and Reloading

12-21-2007, 05:33 PM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

ideally, you want the bullet to be sized .001"...

ideally, you want the bullet to be sized .001" over bore diameter to get a proper seal. At first I was sizing to .311 since thats the closest I had on hand but it was too large. Bullets should be...

Forum: 300 Whisper Ammo and Reloading

11-28-2007, 10:48 AM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

Lee dipper-$10 Old stainless steel or cast iron...

Lee dipper-$10
Old stainless steel or cast iron pot- free if you got one layin around
Hot plate-$5 at walmart
200gr lee rd nose mould- $15
Gas checks- $20 / thou
Lee sizer - $12

Forum: 300 Whisper Ammo and Reloading

11-06-2007, 10:18 AM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

Finally got out to do some testing with the...

Finally got out to do some testing with the Ar-15. The front tube is not a free floater so I have to shoot sans sling, bipod or rest other wise the groups go crazy. This was prone at 50yds, 5...

Forum: 300 Whisper Ammo and Reloading

11-05-2007, 08:16 PM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

I loaded some cast with H335, I had problems with...

I loaded some cast with H335, I had problems with lots of unburned powder, even tried magnum small rifle primers and that didn't help. I'm going to try going to a faster powder, maybe AA 2015 or...

Forum: 300 Whisper Ammo and Reloading

09-28-2007, 01:10 PM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

9.0 grains of H335 was enough to cycle the action...

9.0 grains of H335 was enough to cycle the action properly. I don't know velocity, the chrono got left on the reloading bench by mistake.

Forum: 300 Whisper Ammo and Reloading

09-25-2007, 01:47 PM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

I started getting reliable cycling at 13.4 grains...

I started getting reliable cycling at 13.4 grains of H4227. I use 14 grains to make sure they cycle every time. This load is crankin out at about 1600 fps.

Cast loads as a general rule will run...

Forum: 300 Whisper Ammo and Reloading

09-11-2007, 12:18 PM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

Sorry for the delay in getting back to all ya'll....

Sorry for the delay in getting back to all ya'll. The loads shot just fine, I have at the moment about 1k cast rounds through my del-ton upper 16" flat-top upper, 1:8 twist, carbine gas port at...

Forum: 300 Whisper Ammo and Reloading

06-15-2007, 12:41 PM

Replies: 21

Cast

Views: 6,500

Posted By redneckdan

Cast

My latest experiment with cast in an AR-15. These drop at 191gr from linotype, 255gr with pure lead. I'm gonna try loading them today and see how they shoot. ...

Showing results 1 to 9 of 9

Forum Jump

All times are GMT -4. The time now is 09:28 AM.

Quarterbore.Net Forums