Re-Sizing .311 Projectiles for .300 Whisper...
 

Howdy Gents,

So, I am sitting at my loading bench today sizing a batch of lead boolits to .309 and putting gas checks on and I notice some .311 Speer jacketed projectiles I have. They are there as a reminder to load up some rounds for my SMLE.

I started wondering...can I run these through my sizing die and make them .309 projos that would work for my Whisper???

Anyway, I finished up the lead and thought I would post on here and see if any of you have done anything like this.

I have had a heck of a time finding regular .308-type jacketed projectiles since the "Great Panic of 2013", as I am sure some (or all) of you have had.

I dug out my SMLE because, well...it's a great gun to shoot!
Seriously, the one thing that I have noticed is that there are still p-l-e-n-t-y of .311 bullets to be had.

Just another 'what if?' kind of scenario.

I may just go ahead and re-size a handful and then check them to specs.
I have both a (true) Whisper rifle as well as a 300 BLK SBR.

Food for thought...


Keep The High Ground,


G

You need to get a bullet resizing die to size them down. I have a CH4D die. Be warned, it actually takes a lot of oomph to push a jacketed .311 bullet through a .3085 die. I did a couple thousand ZMax bullets a while back and it was painfully boring. I would just do a little each day, they eventually got done.

Thanks, Hoser.

I have a Lee 308 resizing die and might decide to do this...once I finish up all of the other reloading projects on my bench.

I also found a similar post on the 300BLK forum:
http://www.300blktalk.com/forum/view...t=.311#p740449


Keep The High Ground,


G

How does the Ruger Mini 30, with a .308 barrel handle .311 ammo without problems?

I just ran a hundred85 gr. .312 XTPs through a Lee .308 sizing die to try in the Whisper. They sized down just fine - seem consistent. I'll try loading them over some Trailboss and see how they do. Hopefully I'll get to try them out in a day or two.

Different bullets will react differently to this. I once sized down some .323" 8mm bullets to load in a .318"-barrelled Mauser. The core became loose from the jacket. Turns out the jacket will spring back a bit while the lead core stays smaller, creating looseness. The solution, IF this happens to you (doesn't always), is to size a couple thousandths smaller than your desired final diameter, and then run the bullet through a bump-die to re-expand the whole thing to final diameter. Then, the core and jacket stay firmly swaged together.

I bought 1000 .311sp 123 grain bullets years ago to load in my sks, then the price dropped to about $100 per 1000 delivered. It was cheeper to shoot the mil stuff than reload, so about 5 years ago with my new 300 fireball barrel I loaded up a bunch of the .311sp and fired them through the .308 barrel to break in my new action and get thing loosened up. No problems, just went to sub loads with a can and heavy bullets so haven't shot any for a while now.

I have a complete derail here, but please pardon my ignorance, what exactly do I need to do to load of cast boolets for my 300wtf? I know I need some sort of expander, but going through Midwayusa, I am not sure which one I should be looking for.:confused:

OK, so 7.62x39 dies usually come with two expander balls. One for .308" and one for .310". Using the .310" expander works perfectly for .311" cast bullets in the WTF. Then, you'll slightly bell the case mouth, just as in loading pistol, lessening the chance of shaving the sides of your cast bullets. I use this once the next are expanded with the .311"expander to bell the case mouths:

http://www.midwayusa.com/product/140...-expanding-die

The only thing I would add to your procedure is one of these:

http://www.midwayusa.com/product/548...0-aac-blackout

Give it a light crimp, and you're good to go :-)

Kevin

You can also use the expander in a 303 British die set as well...

Kevin