need some load info on Ramshot enforcer

[lovdasnow]

hey guys, i has some recommended loads from here written down when i ordered some enforcer, but now i can't find my notes. anyway, i just bought 1 pound, but wanted to do a little loading for when my gun gets back next week.

it's a rem 700, 16" shilen barrel, and i have been shooting 220gr SMK's out of it with H110, but i wanted to switch powders because of the temp sensitivity.

so if you guys have a some recipes that i could start low and work up to, that would be great.

when i get my gun done, i'll have to post some pics. i was getting the barrel cut down from 20" and threaded for my SWR trident. also it's getting a matte black duracoat job.
thanks for your time, jon

[Scoots]

Caliber: .300 Whisper
Case length: ca 1.39”/35.3mm
Case Volume: ca 1.62cc (ca 24.95 grains of H2O)
Pressure spec: <50763 psi/3500 bar.
Barrel length: 16”
Powder: Ramshot – ENFORCER.

Bullet weight: 150 grains.
Start load: 8.6 grains (1100 – 1200 ft/p/sec)
Maximum load: 14.0 grains (1775 – 1875 Ft/p/sec).

Bullet weight: 168 grains.
Start load: 8.4 grains (1100 – 1200 ft/p/sec)
Maximum load: 12.3 grains (1575 – 1675 Ft/p/sec).

Bullet weight: 180 grains.
Start load: 8.2 grains (1100 – 1200 ft/p/sec)
Maximum load: 11.3 grains (1475 – 1575 Ft/p/sec).

Bullet weight: 200 grains.
Start load: 7.6 grains (1100 – 1200 ft/p/sec)
Maximum load: 9.7 grains (1350 – 1450 Ft/p/sec).

NOTES:
It’ important to note that SAFETY is the prime concern therefore it is strongly recommend.

TO ALWAYS BEGIN LOADING AT THE RECOMMENDED MINIMUM “START” LOAD.
If at all possible, measure the velocity and correlate with data.

[lovdasnow]

thanks for the info. are those loads you've had good luck with or out of a manual? just wondering, and thanks for your time.

anyone else? i will be loading mainly with the 220 smks.

thanks

[johnshiredman]

Scoots load data is the same I got straight from Ramshot. I just recieved my 16" AR .300 whisper barrel and tried some loads with 180 and 220 round nose. Nothing I loaded cycled a new round, but did eject the spent case (using a YHM phantom 7.62 suppressor). I have some 240 smks that I am loading and will post results hopefully after sunday.

J

[johnshiredman]

I didn't get to shoot the .300 whisper AR with 240 smks and Enforcer today.

I thought I had checked my rounds for proper COL, but when I was at the farm today getting ready to shoot the chamber wouldn't close all the way.

I just finished trying to chamber various lengths and came up with 2.156 for my COL. I had loaded the rounds at 2.170. I'm glad the rounds didn't chamber with the bullet forced against the lands today at the farm...

Anyone else with a .300 whisper AR (not .300-221), know what your COL is with 240 grain SMK's? Just curious what others have found.

Thanks,
J

[lovdasnow]

not a ton of help here because i am shooting a rem 700 and 220gr smk.

but i'm shooting 2.26 COL, and have been fine..??

[lovdasnow]

I could have sworn that i read a few different people were shooting enforcer out of their whispers here, but maybe it was another site..???

anyway, i'll try and post when i get my gun and do some shooting.

anyone else out there shooting enforcer??:grin: