Recommend a place to get my .300 barrel from?

[grey2112]

Going to have an upper custom built. I can get a barrel blank and wonder:

1 - Stainless steel or Chrome Moly?

2 - Twist (mostly going to be subsonic, with occasional supersonic) - 1:8 sound good?

3 - Any good, accurate makers of barrel blanks for this caliber?

4 - Best overall barrel length, again mostly for subsonic, up to 300 yards?

[mooster1223]

1 - Stainless (personal preference)
2 - 1 : 8
3 - Contact a member who goes by "Spook" He has some ready to ship.
4 - Unless you want to register a SBL, 16" is pretty much the standard for an AR subsonic machine. If you were interested in shooting supers and were concerned with reaching a certian velocity, then the answer would certianly be different.

Jim

[grey2112]

1 - Stainless (personal preference)
2 - 1 : 8
3 - Contact a member who goes by "Spook" He has some ready to ship.
4 - Unless you want to register a SBL, 16" is pretty much the standard for an AR subsonic machine. If you were interested in shooting supers and were concerned with reaching a certian velocity, then the answer would certianly be different.

Jim


Well, I do have an SBR registered lower - what length barrel would you recommend then for mostly 300 yard and under subsonic shooting? Is there a point of diminishing returns, or a point where going past would hurt most other loadings?

[dksd39]

+1 for contacting Spook. He is the man with the answers. I have a build going with him right now.

[Fudmottin]

I like CM myself because it is a bit harder than SS. It does require that you do clean it though. Although SS is not immune to corrosion. It really comes down to if you like shiny or parked.

1:8 twist is the only way to fly.

16" is already past the point of diminishing returns for a lot of loads. But if you want to do supers as well, it will give you a few more fps. Also, if you put a can on the end, a longer barrel is easier to suppress. Cycling is more reliable with longer barrels.

My only real problem with SBRs is the regulations about taking them across state lines. The NFA has got to go!

I've got a Douglas 1:8 Premium that should be on its way to me this week. As far as the rest goes, I supplied an A3 upper, vented float tube, and bolt for head spacing that were sourced from DPMS. I don't have the tools to install a barrel myself. Someday.

Paladin Machine did the work. The owner reads this board but I don't know his nick here. He made my custom 223 upper, so the fact I'm going back for the 30/221 says something.

[interceptor]

Well, I do have an SBR registered lower - what length barrel would you recommend then for mostly 300 yard and under subsonic shooting? Is there a point of diminishing returns, or a point where going past would hurt most other loadings?

9.5" is working well for me.

[tp555]

I have a CM blank in 8 twist in stock if your interested.

[Scoots]

Earlier this month I had spoken with a couple of fellows that have freinds that work for Olympic Arms. They told me that Oly will be making another batch of their barrels in 300 Fireball with gas port in pistol position.

From Oly Arms home page:
300 Fireball barrels/uppers: Currently not in production. We have no idea when the next production run for the 300 Fireball barrels will take place. 6-12 months is a reasonable estimate.

[tp555]

I wasn't interested in selling the blank.I can make you a barrel if you want.Thats what I do.I make ar 15 and ar10 barrels.

[morme]

I wasn't interested in selling the blank.I can make you a barrel if you want.Thats what I do.I make ar 15 and ar10 barrels.

I Need an AR barrel 16"-20" 300 Whisper

What to they cost, and how long for delivery?

matthew

[tp555]

I make ar barrels like I said.Discussing who my customers are is bad business.I can tell you who I have made barrels for in the past.I made the 50 AE barrels for Tromix Years ago before Tony Rumore went full time.Pop quiz time.Name 8 calibers .40 and higher than have been made for the ar15.I have made all of them.I'll give you 2 of them,45acp and 50 ae.

[morme]

Title says it all.

tp555, please email me re a 300 wisper 16" barrel

morme@gte.net

morme@gte.net

matthew

[morme]

How do I contact of tp555 directly too have a 16" barrel made?
m

morme@gte.net

morme@gte.net

[tp555]

I sent you an E.regards.

[wombat]

I make ar barrels like I said.Discussing who my customers are is bad business.I can tell you who I have made barrels for in the past.I made the 50 AE barrels for Tromix Years ago before Tony Rumore went full time.Pop quiz time.Name 8 calibers .40 and higher than have been made for the ar15.I have made all of them.I'll give you 2 of them,45acp and 50 ae.

Besides your 45 acp and 50 ae pistol cartridges I can think of:

40 s&w
10mm
400 corbon

Just in 40 cal and these for rifle/shotgun calibers.

.50 bmg
502 Thunder Sabre
.50 beowulf
.499 Leitner-Wise
.458 socom
.450 Bushmaster
.410

I am sure I am missing some? <back on topic> Shot me an email about your barrels too if that is the way you are doing it. </back on topic>

[tp555]

I meant 40 and up.There are 2 in 50 cal.The list"
40 super
40 extreme
440 corbon
44 automag
45 acp
458 socom
50 ae
510 phantom

[stockshift]

I'll second Spook, I got a barrel from him and the transaction went very smoothly. Incidentally my barrel has one of tp555's adjustable gas blocks. I haven't installed the barrel yet as I'm still trying to trim down the gas tube and need to get my hands on a freefloat handguard that will fit over the gas block.

[Fudmottin]

Got this from UPS today. It's a tp555 barrel and block.

http://www.quarterbore.net/forums/showthread.php?t=2334

[tp555]

Get a handguard thats larger than 1 3/4 id.It makes your life easier.The 1 3/4 will work,but its close.You will also have to cut a hole to access the pin if you don't have opennings in the handguard.