Log in

View Full Version : Bolt And Auto!! Finally Here


Richard Malone
01-08-2009, 12:09 AM
AR has been here for a while, Bolt was finished today. AR is M1S upper with custom JP component and DPMS lower. Thanks to Interceptor for all the help.
Bolt is Rem.700,Hart barrel all custom work done by Ray Perry (TX). The Rem.700 fed,fired and ejected without problems. Fired a round into the ground in the backyard. Very quiet. Coyotes BEWARE!!!!!!!!

Colohunter
01-08-2009, 02:39 AM
Those look great, thanks for sharing.

kurtz
01-08-2009, 07:19 AM
AR has been here for a while, Bolt was finished today. AR is M1S upper with custom JP component and DPMS lower. Thanks to Interceptor for all the help.
Bolt is Rem.700,Hart barrel all custom work done by Ray Perry (TX). The Rem.700 fed,fired and ejected without problems. Fired a round into the ground in the backyard. Very quiet. Coyotes BEWARE!!!!!!!!

The rifles look great!!

Ray sure is a great guy.....he shot my CZ Whisper a while back at a match in Lake Charles...trying to remember but was that you at the match also?

Are you in the SE Tx. area....I live in Sulphur but get to shoot at the range north of Bridge City every once in a while....

Richard Malone
01-08-2009, 09:11 AM
That was not me with Ray. He is a great guy and does great work. I live in Port Neches and also shoot at the Orange Gun Club.

kurtz
01-08-2009, 07:22 PM
...... I live in Port Neches......


sorry to hear that.....naw just kidding :smile: ....I work in Port Neches at PNPP, great place and a lot of really great people.....

have you got to shoot the AR much? what load works the best?....

again, rifles look great...


kurtz

Richard Malone
01-09-2009, 02:17 PM
I have about 100 rounds through the AR. 1680 is working the best. 11.2 to 11.4 gr.

interceptor
01-10-2009, 12:39 AM
Rich's 19" bolt gun with Phantom can is definately quieter than my 9.5" AR, also with a Phantom can. We shot them side by side Thursday night. As a disclaimer I was running some of my older loads worked up when I still had the 16" barrel, so..... I dunno, looking for an excuse I guess!

It was interesting hearing the differences in sound. His was like an aggressive pellet rifle and mine had more of a "boom" to it. One thing was obvious: we both need to spend a bit of time working up individual loads for our respective rifles.

(my latest test is Winchester 147gn over 8.3gn of 2400, will try out after the USPSA match tomorrow morning)

Ray did an excellent job on Rich's rifle, the trigger is super sweet! Mine is set to be dropped off to him early next week, but I am going for a 16" barrel.

Richard Malone
01-14-2009, 08:13 AM
Kurtz, just figured out what PNPP stands for. Will be there a few days this week training.
RMalone

kurtz
01-14-2009, 11:25 PM
Kurtz, just figured out what PNPP stands for. Will be there a few days this week training.
RMalone

I'm usually around PO/MTBE at 4640 .....

some friends and I are looking at putting a range trip together this weekend or next at the range off 105 if interested.....

I was at Ray's today to pick up a barrel and get his thoughts for a 'hunter class' rifle so I can shoot with them the next time they come over to Lake Charles....probably do something like a 30x47

sounds like the Phantom is working out pretty good for you.....I've been looking at getting another can, I'll have to check them out.....what is thread mounting size?

kurtz

Richard Malone
01-15-2009, 08:13 AM
I will be working until Monday. Maybe another day. I think the Q.D. is 5/8"-24
RMalone

interceptor
01-19-2009, 12:10 PM
I was at Ray's today to pick up a barrel


sounds like the Phantom is working out pretty good for you.....I've been looking at getting another can, I'll have to check them out.....what is thread mounting size?

kurtz

A cut down, rechambered M1S barrel? I must have just missed you as I was dropping off my new .300 whisper donor bolt gun.


The Phantom cans we use are of the quick disconnect flavor. Work well, but a little heavy, if I decide on another centerfire can I will look into a ti model.

kurtz
01-19-2009, 07:09 PM
A cut down, rechambered M1S barrel?......



That was me :smile: .......had a few of the Model 1s that we rechambered to experiment with other .30 cal cats and one that had never been fired.....took one to Ray to have the chamber cut off and shortened to 10.5"....at some point I'll re-chamber and time and torque the extension to the port, been pretty busy....

Ray said someone asked about the thread protector I was using, if it was ya'll it's the Schuster (http://www.midwayusa.com/eproductpage.exe/showproduct?saleitemid=999271)

I've got a couple thread on cans, one is a two-point type and is probably my favorite although it is a little heavier than the single point....