Log in

View Full Version : Yet Another M1S Upper Report


Flewis
07-04-2008, 02:21 PM
I hate to start another thread, but didn't want to hijack anyone else's either.

I just got a new M1S upper (a week or so ago):

A3 Upper, 16" 1:8 twist with a chrome bolt and carrier (based on people's recommendations that the chrome bolt cycles easier... seems to work). Gas port is at the carbine position.

I cleaned the upper and lubed the bolt well.

Also, I'm using standard GI 20 round mags and a 6 position carbine stock with the stock spring and plunger.

Oh, also the gas port is .125. Strangely enough when I called M1S and asked if their .300 Fireball upper would cycle sub-sonics they said no. Then I asked what size the gas port was and after checking she said .125. I can't image it would be much good to shoot a super-sonic load with that size port and no adjustable gas system, but...

I'm setting this up for strictly sub-sonic 220 SMK loads.

Ran five rounds of H-110 w/9.2gns and the first two shots cycled completely, the remaining three ejected but did not strip the next round. They were all running slow at around 950 fps.

The next five rounds was 13gns of Reloader 7. All cycled properly and the bolt locked back after the last round. Ran about 1200+ fps. A little fast. I had one or two pierced primers, but no other pressure signs.

Last was five rounds with 11.5gns of 1680. Ran about 1050 fps on average and all rounds cycled properly. Also had a couple of pierced primers, but no other pressure signs.

I'm using Winchester small rifle (WSR) primers. I've read that they're a little soft (never had any trouble with my .223 loads though). I'm going to try some CCI-41 milspec primers next time.

Also, COAL was around 2.160

So far I'm very pleased. Today I'm loading up some more and am going to see how the accuracy is. I also picked up some PMags since everyone seems to like them.

If anyone's interested, I can post my spreadsheet with the trim to, COALs, brass and primer types, velocity's, etc.

kdiver58
07-07-2008, 01:12 AM
I use CCI-450 primers with no problems ..

kdiver58
07-07-2008, 01:18 AM
If you look at a few of my last posts .. we are doing many of the same things :)

My M1S upper will cycle some sub-sonics.. I found the trick with mine was the powder burn rate. I'm sticking with 1680 or slower ..

My M1S upper is a 1 to 1.5 MOA gun .. I consider it a base on which to build a better whisper .. After I get my suppressor and get it all dialed in I'm going to re-barrel !

Flewis
07-07-2008, 08:54 AM
Yes, I'm going to stick with AA1680 also. It's given me the most consistent velocities and has always cycled the rifle.

Still experimenting with loads. I tried the H110 with a little hotter load and got around 1150 fps... still wouldn't cycle the rifle reliably so its out as far as my rifle is concerned.

I started out at 50 yards zeroing the rifle in. With the AA1680 loads I put five shots all on top of each other, pretty much the same hole. Moved it out to 100 yards and the group opened up to about 2 inches... but I'm blaming that on myself (it was hot, I was tired, and the target was in a heavily shaded area so I couldn't see it very well). Going to try again in a few days.

KDiver, what barrel are you looking at going to?

How do you guys deal with the amount of drop the Whisper/Fireball has at sub-sonic speeds? With my .223 varmit rifle I can guess the distances close enough to put a round in a 'chuck's head up to 200 yards or so. Looks like with the .300 I'll need a range-finder... it drops 4.5 inches from 100 to 125 yards if you zero at 100.

kdiver58
07-08-2008, 02:42 AM
I mounted a scope with mil dots and lots of travel in the knobs. I was lobbing them out to 300 yards and had over 9 feet of drop :)
But I was able to hit a 12 by 12 plate at the distance..

BTW it's a Falcon Menace 10X

320pf
07-08-2008, 09:18 AM
I hate to start another thread, but didn't want to hijack anyone else's either.

I just got a new M1S upper (a week or so ago):

A3 Upper, 16" 1:8 twist with a chrome bolt and carrier (based on people's recommendations that the chrome bolt cycles easier... seems to work). Gas port is at the carbine position.

I cleaned the upper and lubed the bolt well.

Also, I'm using standard GI 20 round mags and a 6 position carbine stock with the stock spring and plunger.

Oh, also the gas port is .125. Strangely enough when I called M1S and asked if their .300 Fireball upper would cycle sub-sonics they said no. Then I asked what size the gas port was and after checking she said .125. I can't image it would be much good to shoot a super-sonic load with that size port and no adjustable gas system, but...

I'm setting this up for strictly sub-sonic 220 SMK loads.

Ran five rounds of H-110 w/9.2gns and the first two shots cycled completely, the remaining three ejected but did not strip the next round. They were all running slow at around 950 fps.

The next five rounds was 13gns of Reloader 7. All cycled properly and the bolt locked back after the last round. Ran about 1200+ fps. A little fast. I had one or two pierced primers, but no other pressure signs.

Last was five rounds with 11.5gns of 1680. Ran about 1050 fps on average and all rounds cycled properly. Also had a couple of pierced primers, but no other pressure signs.

I'm using Winchester small rifle (WSR) primers. I've read that they're a little soft (never had any trouble with my .223 loads though). I'm going to try some CCI-41 milspec primers next time.

Also, COAL was around 2.160

So far I'm very pleased. Today I'm loading up some more and am going to see how the accuracy is. I also picked up some PMags since everyone seems to like them.

If anyone's interested, I can post my spreadsheet with the trim to, COALs, brass and primer types, velocity's, etc.

Flewis,

Here is some load data from the Sierra manual for 220 gr MK. These are the starting loads, so you should not be getting any pierced primers. Even with the Winchester primers. (I use Winchester primers and have not pierced any primers. Even with the max loads that I have worked up to.)

I suspect that there is something wrong with the firing pin and/or the bolt/carrier. I would call M1 and ask them to send you another bolt/carrier and firing pin.

AA#9--9.4 1000 fps
2300--10.0 1000 fps
VN110--9.4 1000 fps
H110--9.9 1000 fps
W296--9.8 1000 fps
VN120--11.5 1000 fps
AA1680--11.7 1000 fps

320pf

P.S. Check out the pride fowler scopes. The 22LR has nearly identical ballistic trajectories and the 330-221 fireball sub-sonics.

kdiver58
07-08-2008, 09:31 PM
Wow I need to check that out I have a Pride Fowler RR scope on my 10/22!

Oh I was going to order a Shilen barrel blank and machine my own.. But that's down the road .. K

320pf
07-09-2008, 08:45 AM
Wow I need to check that out I have a Pride Fowler RR scope on my 10/22!

Oh I was going to order a Shilen barrel blank and machine my own.. But that's down the road .. K

This is a bit off topic but people might find this useful.

Here are the ballistics for a Sierra 220 gr MK at 1080 fps compared to a Sierra 40 gr hornet varminter bullet at 1230 fps. I know that the 40 gr varminter bullet has a better B.C. but it still demonstrates the ballistic similarities between sub-sonic 300-221 fireball loads and the 22LR. Out to about 200 yrds., the ballistics are close enough. If you are looking for a scope to use with sub-sonic loads the Pride Fowler might be considered.


Calculated Table Sierra 220 MK at 1080 fps
Range Drop
(yds) (in)
100 -0.0
200 -30.8
300 -96.3
400 -199.0
500 -341.1

Calculated Table Sierra 40 gr at 1230 fps
Range Drop
(yds) (in)
100 -0.0
200 -32.9
300 -110.6
400 -243.9
500 -445.0


http://www.rapidreticle.com/img/22LR3-9.jpg

320pf

Flewis
07-09-2008, 10:21 AM
Thanks for the info guys. On the pierced primers, I had no problem using the CCI-41s. I will check the firing pin length and compare other specs to the bolt in my .223 AR which I've had no trouble with using the WSR primers.

I did notice that the ballistics are pretty much identical to the CCI Standard Velocity (sub-sonic) .22 LR that I shoot a lot of. Now that I think about it, they should be the same other than a slight adjustment for the difference in drag between the .22 and .308 bullets.

I'm loading up another 50 rounds and going back out in a few days to dial it in at 100 and 200 yards. This time using new .223 brass to form the cases and AA1680 powder.

I have a box of .221 Fireball brass that I've formed a few cases from. Many of them look like the neck isn't exactly centered on the cartridge body, which I've read can be a problem when necking up the .221 brass. I hand picked the best looking ones and have used them in my load/velocity testing. If I use the rest of those .221 cases to make .300 Whisper brass, should I expect to see a degradation in accuracy? Just wondering if I should bother necking the rest of those up...

Pitt300
07-09-2008, 10:17 PM
I too have a mildot scope w/target turrets.
I've found it easiest when I switch to subsonic loads to simply crank in about 13-14" of UP elevation & then hold dead on the target @ 100 yards.
This is NOT the problem.
The problem comes into estimating 140/150/160 yards as the drop gets severe.
A 200 yard range finder would be ideal!
If you know the distance, it's very easy to dial in elevation & wind drift is minimal w/220 & 240g subsonics.
I use H-110 & VV N-110 w/all loads & everything cycles fine w/M1S upper & A2 stock w/A2 spring & CAR buffer.

kurtz
07-09-2008, 10:30 PM
I too have a mildot scope w/target turrets.
I've found it easiest when I switch to subsonic loads to simply crank in about 13-14" of UP elevation & then hold dead on the target @ 100 yards.
This is NOT the problem.
The problem comes into estimating 140/150/160 yards as the drop gets severe.
A 200 yard range finder would be ideal!


Don't know if this will help, I use a 4.5x14 Mark 4 .....I do similar as you do except I zero at 100, a crank of 7" puts it pretty close at 140 to 160.....a crank of 14" puts it dead on at 200 with 220gr SMK at 1,050fps....

kurtz

Flewis
07-23-2008, 11:05 PM
Well, I loaded up 50 rounds of the following:

Cases formed from new Winchester .223
trimmed to 1.365
11.6 grains of AA1680
220 grain SMK
COAL at 2.170

All 50 cycled perfectly and the spent brass all looks good.

Shooting from a bench with good sand bags.

However, accuracy sucked at 100 yards. I'll post pics of the targets in a little bit. The groups were large and strung diagonally. I'm using a lower with a match trigger that usually has my .223 varmit upper on it (which I can shoot dime size groups with all day long at 100 yards).

Any ideas on what I should look at for the accuracy problem? I have a cheap scope (NRA Brunton 6-24x50). I'm wondering if it isn't holding zero for some reason.

From the targets, it looks like the 220s are stabilizing (no keyholing). The velocities are all within about 30 fps of each other. How much velocity difference does it take to really start throwing shots? I'd like to get this rifle down to inch or inch and a half groups at 100 yards.

http://rx7.voodoobox.net/images/M1SFireball.jpg

http://rx7.voodoobox.net/images/Target1.jpg

http://rx7.voodoobox.net/images/Target2.jpg

kurtz
07-24-2008, 12:12 AM
On my AR whispers, supersonic fire-formed brass seems to be more accurate than first formed subsonic brass....you may also try pushing the load a little faster, even if it goes supersonic, just to see if the groups tighten up....my most consistant accurate 220SMK loads are just on the supersonic side, most of the subsonics are right at 1" or a little bigger....my more accurate loads are set right at the lands or slightly engraved....

Flewis
07-25-2008, 10:16 AM
On my AR whispers, supersonic fire-formed brass seems to be more accurate than first formed subsonic brass....you may also try pushing the load a little faster, even if it goes supersonic, just to see if the groups tighten up....my most consistant accurate 220SMK loads are just on the supersonic side, most of the subsonics are right at 1" or a little bigger....my more accurate loads are set right at the lands or slightly engraved....

Thanks, I'll try both if those suggestions.

The barrel twist is 1:8 (confirmed). That should work well with the 220s, right?

kurtz
07-25-2008, 05:14 PM
Thanks, I'll try both if those suggestions.

The barrel twist is 1:8 (confirmed). That should work well with the 220s, right?

1:8 ~ 220SMK....that is correct....

Pitt300
07-25-2008, 05:21 PM
Kurtz,
Going to try some of the 208 AMaxs on Sunday.
I'll give it a +21" of clicks & shoot @ 200yards.
I have no intermediate targets except 25, 50, 100, 200y.

interceptor
07-27-2008, 06:02 PM
Hope the A Max's work for you. Mine didn't.:mad:

Been thinking... If the accuracy of this M1S upper doesn't improve, I'm either gonna go one of two ways with it. One: rebarrel with (insert reccomended brand) and length. Two: get another tax stamp and cut it back to something like 8 inches or so, redrill the gas port to the pistol location, reinstall my Phantom adapter and YHM can and cover it with a 12" free float tube so the can just sticks out some and have a smith build me up a bolt action whisper on a Rem700 action.

Really leaning toward option 2. This one is pissing me off so far.

Flewis
07-27-2008, 08:42 PM
Anyone know of a place selling .300 Fireball barrels now?

Novekse doesn't, AR15Barrels.com seems to be gone, SSK won't sell just the barrel and so on...

kdiver58
07-28-2008, 05:06 AM
Just get a (insert barrel maker here) and have a good AR-15 smith ream it and thread it... That's what I'm going to do once I get the rest of the bugs out.
I'm not as unhappy as interceptor .. but it could be a LOT better ...

Pitt300
07-28-2008, 09:31 AM
Interceptor,
Did you get free float hand guards from M1S?

cubflyer75
07-28-2008, 10:48 AM
Flewis, I would try another scope before writing off the barrel. I have a rem700 .223 20" bull that I was developing some loads for. At 100yds, with 100% match prep brass and 53gr SMK's, I would get 2 in the same hole, then point of impact would shift almost 1.5". Then another 2 shots in the same hole, then different POI. My scope was a BSA (read cheapo) and it was mounted rock solid. Changed scopes, and 5shot/1hole groups @100 yds. From looking at your group, I suspect that your scope mounting or internals(most likely) are moving. YMO. Mike

JFettig
07-28-2008, 02:25 PM
I second that notion, get a decent scope. I had a bsa scope once on a .223 AR, I could never hit anything, changed scopes and my groups are sub MOA. Each time I took it out it would have a different zero.
The best cheap scope that I've found is a Tasco Target Varmint 2.5-10 mil-dot. I've been using one for 3 years, haven't touched the zero and have put over 1 thousand rounds through the gun. That and I remove it after every time I take it out(I have a 1 piece M1S mount).

Jon

Flewis
08-01-2008, 10:00 PM
Well, I tried a different scope that I know is good and got the same results.

I also tried some faster loads, but didn't make it very far into the supersonic range. I'm going to try some hotter loads and also try some 208 gn Hornadys.

I think someone, somewhere, posted that their M1S upper came with a loose barrel nut... is there an easy way to check that? There isn't anything obviously loose on the upper.

interceptor
08-01-2008, 10:41 PM
Interceptor,
Did you get free float hand guards from M1S?


Nope. On this build I used a Hogue FF tube I had.

Flewis
08-02-2008, 07:37 PM
Well, tried some super-sonic 220 SMKs and some sub-sonic 208 AMaxes with the same results... the target looks like a shotgun pattern. Just to make sure it wasn't me I ran 5 rounds through my .223 upper and all the shots overlapped.

I'm finished wasting ammo in this thing. I dropped it off at the gunsmiths this afternoon to let him go over it and see if he can find a problem.

I asked this before, but I think it got lost in the thread... anyone know where I can buy a good, match quality .300 Fireball barrel?

snowhack
08-02-2008, 11:57 PM
I mounted a scope with mil dots and lots of travel in the knobs. I was lobbing them out to 300 yards and had over 9 feet of drop :)
But I was able to hit a 12 by 12 plate at the distance..

BTW it's a Falcon Menace 10X



I fell in love w/ that scope just reading about it....saw it @ Sniper Central. How do you like it? Do you have the MP-5 reticle or Mil dot?

Sorry to side track. You can PM me so we can stay on track.

I have the M1S upper only w/ out the chromed bolt. Cycles like sand in your shorts. (it's pretty new yet) Will not cycle properly w/ H-110, Reloader #5 or #7. I was going to change up the gas port location and get an adjustable block, play w/ springs and buffers and more polishing of the bolt carrier. I'm going to try the AA powder first I guess. Especially since Bushmaster has a conversion kit for gas piston. (@ about $399.)


Wow sorry guys I replied to a post from the first page...should'a checked the lower right first.


Did you have the bore, grooves and lands checked w/ a scope? You may have had a lemony fresh barrel installed. My M1S upper is pretty consistant down range w/ all loads even being "pre-broken in". I inquired w/ M1S about the key hole forge marks out of curiosity and they told me of many diff forge houses supplying their cast parts. Not sure of the barrel man, but a lot of diff resources sometimes means a broad range in tolerence and fit. What about straightness and the crown? I know most times this goes w/ out mention for most here and I don't mean to insult intel, but you sometimes forget a thing or two.

interceptor
08-03-2008, 12:46 AM
My barrel was recrowned at the same time as it was threaded for the Phantom adapter for the can, 11 deg.


<---- NOT a sastisfied M1S shopper...

kurtz
08-03-2008, 01:23 AM
Well, tried some super-sonic 220 SMKs and some sub-sonic 208 AMaxes with the same results... the target looks like a shotgun pattern. Just to make sure it wasn't me I ran 5 rounds through my .223 upper and all the shots overlapped.

I'm finished wasting ammo in this thing. I dropped it off at the gunsmiths this afternoon to let him go over it and see if he can find a problem.

I asked this before, but I think it got lost in the thread... anyone know where I can buy a good, match quality .300 Fireball barrel?

last week this thread piqued my interest....I ordered everything to assemble a Model 1 300 Whisper 16" free float tube upper.....shot it Friday...after trying every make shoot trick I knew, the best I could get after around 200 rounds was about a 4" group at 100yds.....Broke it down today rechambered it in 7.62x40 thinking it might be a chamber issue and shot it today....similar results:mad: ......now that I have a base line I'm going to tear it down again and slug/check the bore and close off the port....shoot it as a single shot and hope start moving forward....

did toggle two different Mark 4 scopes between this upper and a 24" .223 upper, sighting in after moves.....the .223 would print finger nail sized groups at 100yds with either scope....the Model 1 would shoot about 1.5" at 25yds:eek:

I'll post what I find out...

Kurtz

interceptor
08-03-2008, 01:26 AM
Say it with me now.... "MODEL 1 SUCKS".


Now, does anyone know of a source for GOOD 300 whisper barrels, and I'm guessing not SSK as I don't think they will sell just the barrel.

kurtz
08-03-2008, 01:34 AM
Say it with me now.... "MODEL 1 SUCKS".

Laughing my ass off:grin: .....It is what it is, an inexpensive blaster.....my SSK AR will shoot sub-MOA with just about anything you stick in it, but it cost probably four times as much as the Model 1 stuff, but it works...thanks JD....

I haven't checked the Model 1 yet but just from running a jag and brush....it feels tight, tight, tight....or may be over sized and rough as hell....

ETA: I just remembered....I helped a friend from Texas put together a .223 Model 1 gun about a month ago....don't know if they do this to all of them but the chamber and bore was phosphate finished, or something black and rough....the chamber was so rough that it wouldn't cycle smooth with light reloads until we polished it out, but even at that it would shoot better than 4" at 100yds....

interceptor
08-03-2008, 02:08 AM
Sounds like they are not plugginug the chamber and bore when parkerizing. Shoddy.

Flewis
08-03-2008, 11:52 AM
The gunsmith I left mine with is a good one. I asked him to go over it in detail to see what the problem was. I'll let everyone know what I find out.

hugginsvilleH&A
08-03-2008, 04:06 PM
this sucks, I just got a M1S hope it goes better than that, do these barrels have a break-in period? is there anyone getting any good results from their M1S, give me a little hope there has got to be some good results somewhere???

Pitt300
08-03-2008, 04:23 PM
http://www.quarterbore.net/forums/photopost/showphoto.php?photo=384&cat=562 125g Nos BT

http://www.quarterbore.net/forums/photopost/showphoto.php?photo=452&cat=562 220g SMK

Sorry you all are having so much trouble.
Mine shoots great after tweaking loads.
Above is sample & I'm getting 1/2" w/subs.
See my photo album w/data on images.
I almost always fire lap my barrels w/LBT soft lead slugs & his lapping compound.
Did it to my M1S. Doubt that it made a huge difference but I do believe it helps almost every barrel I do it to.

hugginsvilleH&A
08-03-2008, 07:12 PM
so Pitt how did you go about fire lapping your barrel? was there any other little tricks you may have done? surely these M1S cant all be bad, what are the odds,,,,

I was wondering if the problems were not charge related, half a grain can sometimes throw things way off, had that happen with a LM the charging chain link kept going up/down a link every other pull and was getting crazy results from 2 different guns,very frustrating till I figured out what was happening , fix it and has been smooth sailing every since.

Pitt300
08-03-2008, 09:20 PM
My 1st question is how good is your shooting w/a KNOWN accurate rifle?
How good are your scope/rings & mount/rest & shooting technique?
How's your trigger?
Hand guards free floated?

Start shooting w/the 125g Nos BT's @ supersonic.
These tend to shoot good in everyones guns & this will let you see accuracy potential.
Subsonic is next after your SURE the gun is 100%.
Subsonics can be frustrating & you need a chronograph to confirm your loads & remember they can be/are temperature sensative.

There are a LOT of things that will effect accuracy BEFORE you ever pull the trigger.

This is Wheeler's kit from Midway BUT I like LBT's below.

http://www.midwayusa.com/midwayusa/StaticPages/pdf/Instructions/Bore%20Lapping%20Kit%20Instr.pdf

http://www.midwayusa.com/eproductpage.exe/showproduct?saleitemid=646612&t=11082005



LBT is at : http://www.lbtmoulds.com/index.shtml

You'll need his LAP kit & 20-40 of HIS .308 SOFT LEAD bullets.

I load about 10-15 of them subsonic which should be easy for our group.
Dip the tip of the loaded cartridge in the lap compound just like dipping an ice cream cone in a pot of hot chocolate syrup.
Carefully load directly into chamber.
Shoot so that you KNOW it has left barrel-fire thru chrono/into pond @ steep angle so no ricochet/into target or dirt berm where you can see impact.
Do about 10 w/compound & then shoot 3-5 w/o just to "wipe" out the barrel.
Then clean the HELL out of it.
Now see how it does.
May need to do again.
He recommends covering the bullets w/compound/rolling between 2 steel plates to totally get it in all of the gas check rings/put this wet bullet in your reloading press over your primed & charged case/seat it/wipe compound off outside of case & Then clean up the dies.
My technique is how he tells you to do .22 soft lead bullets.
I'll probably start a shit storm w/this but I've had very good luck w/his products & my technique.
Try it if you like!
Don't if your not interested.
Works for me & I think my groups show that it did not hurt the barrel.

kurtz
08-03-2008, 11:25 PM
I'll probably start a shit storm w/this but I've had very good luck w/his products & my technique.
Try it if you like!
Don't if your not interested.
Works for me & I think my groups show that it did not hurt the barrel.

Pitt, the lapping looks like it may do the trick....I'm game to try it....

I ran a slug down the barrel today and found that the Model 1 bore was pretty tight....the slug checked at .306 and .301 (also confirmed the .301 bore with a reamer pilot)....my tightest .308 that I know that shoots good is a Palma and checks at .3075 and .298....my others go out to as much as .3085...

I remember about 15 years ago that a rifle manufacturer had to make changes to their production line because their barrels were about .002" too tight and causing out of the box accuracy problems....they made a change to free up the bore a little and the accuracy came back around....

Pitt, thanks for the info...

kurtz

Flewis
08-04-2008, 12:30 PM
I remember about 15 years ago that a rifle manufacturer had to make changes to their production line because their barrels were about .002" too tight and causing out of the box accuracy problems....they made a change to free up the bore a little and the accuracy came back around....

kurtz

I have noticed more than the usual amount of copper jacket material in my bolt when I am cleaning the rifle... makes me think this might be my problem.

This may be a stupid question, but if a bore is too tight, can it be re-rifled for that small amount or is it scrap?

ranger dave
08-04-2008, 12:56 PM
the best all around load i have worked up is 8g of 2400 with a 147g win fmj the bullets are about half the price of a match king . id go broke feeding my whispers mk every time i shoot

kurtz
08-04-2008, 06:38 PM
I have noticed more than the usual amount of copper jacket material in my bolt when I am cleaning the rifle... makes me think this might be my problem.

This may be a stupid question, but if a bore is too tight, can it be re-rifled for that small amount or is it scrap?

I single shot fired a few of the Hawk bullets out of my Model 1....the Hawks mic a little under .309.....after firing and running a chamber brush in I pulled out a perfect ring of copper jacket....looked like a little hoop ear ring....

I have never had to lap a barrel before, most of the ones I have cleaned up through normal break in/shooting, but I'm willing to try it as tight as the bore is on this one....should be able to free it up the .0015 or so and smooth out the tool marks....I don't think it would be necessary to re-rifle it for that amount, and I think getting a button to match up with the current cuts might be a little tough....

I probably won't be able to mess with mine for a week or so but I'm going to give the lap a try....

hugginsvilleH&A
08-07-2008, 08:39 AM
thanks pitt for the info that sounds like you got yours dialed in pretty good , will try the fire lap , thanks again, great info

Pitt300
08-07-2008, 09:10 AM
Lapping is just something else to try.
It will NOT cure any major mechanical problems w/gun.

Flewis
08-07-2008, 10:29 AM
Well, a gunsmith at the shop I use looked at the M1S Fireball... unfortunately he wasn't the one I normally deal with and I'm not impressed.

He said the barrel nut was fine.

He then put a bore-sighter on the rifle and said the scope changed zero when you tapped on it. Personally, I think he was moving his bore-sighter when tapping on the setup because I took the scope back home (same rings too), put them on my .223 rifle and shot repeated 5 shot groups at 100 yards that were all under 1". I also think it would be odd to have two separate scopes that shot the same poor groups (since this is the second scope I've tried).

I asked about the bore diameter and he said it couldn't be too tight since his .30 cal bore-sighter fit in the bore. I quit listening at that point.

Anyway, I called Paul at M1S and he was a great guy to talk to. He asked that I send the upper back to him with some of my spent brass and he would find out what the problem was. So far I'm pleased with M1S's support, Paul really seemed to be interested.

snowhack
08-08-2008, 02:38 PM
I see a lot of flack sent toward M1S, but I agree that their service and people skills are pretty good. Some places don't even respond to e-mails or general questions. When they do it's a ganeric answer, weeks or months later or incomplete or rude. M1S is not a gun builder just a supply hub, basically, w/ a small capacity to tech and assemble parts. They get their parts from verious forge houses and manufactures and assemble them.


SIDE NOTE: Mine has the "key hole" forge mark on the upper, some others do not. Look at some of the "big" manufactures and notice that same key hole mark...Remington's new R-15, Stag's ARs, S&W's AR, etc...they all have it. M1S just cuts out one of the middle men.

kurtz
08-16-2008, 09:34 PM
I probably won't be able to mess with mine for a week or so but I'm going to give the lap a try....

I ended up hand lapping mine using the borebrush / patch method doing 400 strokes with 800 grit lapping compound...then fire lapped with 8 shots of long bearing surface sub-sonic 220s coated with polishing compound.......

It worked :smile: .....groups went from 3 and 4 inch to a little over 1"......velocity came up and pressure signs on some of the hotter loads went away.....thanks Pitt300


kurtz

Flewis
08-17-2008, 07:15 PM
I ended up hand lapping mine using the borebrush / patch method doing 400 strokes with 800 grit lapping compound...then fire lapped with 8 shots of long bearing surface sub-sonic 220s coated with polishing compound.......

It worked :smile: .....groups went from 3 and 4 inch to a little over 1"......velocity came up and pressure signs on some of the hotter loads went away.....thanks Pitt300


kurtz

Can you give us instructions on what you did? Where did you get the compound? Did you just coat a patch and run it up/down the barrel?

kurtz
08-17-2008, 10:33 PM
Can you give us instructions on what you did? Where did you get the compound? Did you just coat a patch and run it up/down the barrel?

I had never done one myself until this one.....did a few google searches, found a couple different ways to do it, picked the way that suited what equipment I had...

- need a strong cleaning rod, I used a Tipton
- a .30cal bronze bore brush, one with a little use on it so it can be pulled or pushed the other direction without being removed from the bore.
- a pack of 3"x3" patches, I used Outers 42357
- 800 grit lapping compound, I got mine from Brownells
- bottle of Break Free CLP

fold a patch in half over the brush....saturate it with CLP....insert it from the receiver end to the beginning of the throat.....put a mark on the cleaning rod even with the end of the receiver, I used a paint pen.....push it through the bore until about half of the patch comes out the muzzle.....put another mark on the rod.....practice pulling and pushing the rod from mark to mark, the patch will take on a shape almost like a cylinder.....pull out and change the patch.....repeat with CLP only for 8 or 10 passes to shape the patch.....pull out and wipe a coating of lapping compound on the patch.....insert and lap from mark to mark, I changed the patch about every 25 passes....I did this for 300 passes.....then switched to pushing the lapping compound coated patches from chamber end to muzzle end.....the easiest way I found to do this was to thread the brush on the rod just a couple turns.....push the patch from chamber out the muzzle.....spin the brush a couple times, unthread it from the rod.....pull the rod out...thread the brush back on....push through to muzzle....repeat until done.....clean the hell out of everything when finished.....

fire lapped for 8 shots as previously described......

not saying it will work in every case but it worked in mine after finding out the bore was pretty tight...

shot over 200 round of various loads today....all groups were under 1.25"....much better than the 3" and 4" groups I was getting with the same loads.....

hope this helps...

kurtz

Flewis
08-18-2008, 11:14 AM
Thanks for the info Kurtz!

A little update on mine. Paul at M1S has the upper and left me a message saying that he didn't see anything on visual inspection. Sounds like he is going to take it to the range early this week and see if he can repeat my problems and find out what is causing them.

Now for a new twist. I was at the gunshow last weekend and spoke to the J&T Distributing/Doublestar guys. I own one of their stainless bull barrel target uppers in .223 that I'm very pleased with. I noticed they had .300 Whisper in their catalog and asked them about the barrels. The guy said they didn't have any at the show but just got a new shipment of them in a couple days before.

I called J&T the following Monday and asked about the barrels. They're ER Shaw (same that M1S uses I think) with 0.125 gas ports at the carbine position. They were in the catalog as .300 Whisper and I asked the guy on the phone if they were true Whisper or 300-221 Fireball. He said they were Whisper. I went ahead and ordered an upper set up in the same configuration as my M1S. It arrived last Friday. The barrel is stamped .300 Whisper but the chamber appears to be the same length as my M1S at 2.180 max COAL.

I cleaned it thoroughly and shot it Saturday. It wouldn't cycle with the loads that I got working on the M1S. I took the gas block off and checked the ports. The barrel port was 0.125. The problem was the gas tube wasn't aligned properly in the gas block. It was blocking about half the port (the tube needed to be further back in the block). It is pinned in the block so the easiest solution was to just run a drill bit down in the block to take some material off the gas tube. After fixing that it cycled flawlessly.

So far the results are promising. I got about 1 inch groups at 100 yards with sub-sonic 220 SMKs and 208 AMaxes and that was with the first 40 rounds. I expect better as it breaks in. Also, it doesn't gouge my brass no matter what magazine I use. I won't be able to compare feed ramps until I get the M1S upper back.

snowhack
08-19-2008, 11:00 AM
I see a lot of flack sent toward M1S, but I agree that their service and people skills are pretty good. Some places don't even respond to e-mails or general questions. When they do it's a ganeric answer, weeks or months later or incomplete or rude. M1S is not a gun builder just a supply hub, basically, w/ a small capacity to tech and assemble parts. They get their parts from verious forge houses and manufactures and assemble them.


SIDE NOTE: Mine has the "key hole" forge mark on the upper, some others do not. Look at some of the "big" manufactures and notice that same key hole mark...Remington's new R-15, Stag's ARs, S&W's AR, etc...they all have it. M1S just cuts out one of the middle men.



kind'a sounds familiar...........

interceptor
08-25-2008, 10:04 PM
Well, you have all heard me bitching about my M1S upper lately. Last load through it was 9.3gn H110 and Hornady 208gn A-Max, printed a group of roughly 5-6" at both 100 and 200 yards. This sucked.

Now, segway to Sunday's range session.

Same gun, same ammo, same everything. Brought a pile of ammo of the previously mentioned ammo just for fun, ran a little through the chrono, then shot a group for sh!ts and giggles. To my surprise it now posted a true 1 MOA pattern at 100 yards. Fluke, so I did it again, and again. Same result.

So, the gun/ammo that ran minute of bad guy at 100 now is a MOA. Go figure. Maybe it sensed my vile thoughts towards it and decided to straighten up and run right for fear of going under the lathe. Who knows...?

At any rate, I'm out of the 208's, now have a stock of 220 SMK's. Will stick with them.

BTW, 11.8 gn AA1680 and 220 gn SMK loaded to a OAL 2.200" delivered an average 10 round string of 1025fps. No report on accuracy yet, sad to admit I just put them in the berm and not at a target, but I'm off to the bench to cook up some more.

interceptor
08-26-2008, 02:33 PM
There shouldn't be this many people with issues regarding a certain manufacturer and item. Public forums like this one exist so that future potential buyers can know what they are getting into with a product. Knowing what I know now I would have went with a DelTon or ordered a Noveske barrel and built my own.

Even now that it is working I won't buy from M1S again.

Lemme put it this way... If you went down to your local dealership and bought a new car, got it home and it wouldn't start and then you had to go into the engine and fix some things would you have a positive report for that manufacturer, considering that it is now running but wasnt' when you bought it and should have been?

Flewis
08-26-2008, 07:14 PM
Paul at M1S has my upper and is testing it right now. I've spoken to him a couple of times as he is asking if it is ok to do this or that to it. I'll have to say that I'm truly impressed with the level of customer support they have. Paul seems very interested in finding out what is going on with it.

If they make it right I'll definitely do business with them again. Every company has issues from time to time, its how they deal with them that concerns me.

I should hear something back from him this week. I'll let everyone know what I find out.

GlockandRoll
09-05-2008, 08:30 PM
So, I'm confused... did the lapping fix the problem?
I've built more than a dozen M1S guns for friends and family, and have always noticed they didnt shoot very well untill broken in.

kurtz - thanks for all you wrote, it was very informative.

Eviltwin
09-23-2008, 11:55 PM
Please let us know if you've heard back. I'm serious about getting a AR-15 upper in .300 Whisper / .300x221 and the price difference between M1S/J&T or SSK is pretty substantial (about the cost to get an aimpoint or eotech).

GlockandRoll
09-24-2008, 12:30 AM
I'm all but giving up on the caliber... every time it makes sense in my head, I realize that it is not a mainstream round.

In the end, a 77/44 does an incredible job of putting a hurt on something 200 yards away - yet virtually silent from the shooters perspective.

Pitt300
09-24-2008, 10:09 AM
I spoke w/Paul this weekend & he had someone's upper & it shot excellent.
Not sure whose it was.
Think it was someone in North Texas & think he may have even shot w/the owner of the upper & the upper was not a problem.
See if someone chimes in.
Mine just shot 3 sub 1" groups w/208 AMaxs last week.
Used 8.8, 9.0 & 9.2 g VV N110.
Didn't chrono just shooting.
For some reason my 9.4g loads went supersonic on my & it wasn't that hot outside so I backed down a little.
All 3 of these were subsonic & w/in about 1 1/2" of POI.
Hope this helps.

Eviltwin
09-24-2008, 09:15 PM
Mine just shot 3 sub 1" groups w/208 AMaxs last week.


I know you've probably posted it elsewhere but what upper do you have?

Pitt300
09-24-2008, 11:54 PM
M1S w/16" Freefloat tube w/gas port in carbine position on a DPMS lower

hugginsvilleH&A
09-26-2008, 10:35 AM
pitt I did my M1S with the wheeler kit , has a very nice shiny/smooth bore and the thing shoots fantastic, no problems at all. The stuff here had me spooked with the problems some are having but I would buy another M1S, when I get mo' money. The thing shoots really sweet( sub 1") I'm shooting 220SMK some over 1680 others over 4227, I'm happy with both , thanks pitt for the lead into the firelapping realm...... you tha man! :cool:

Flewis
09-30-2008, 02:12 PM
Hey, sorry it has taken me so long to follow up on my M1S.

Paul at M1S wound up re-crowning the barrel and was able to shoot 1" groups with sub-sonic 220 SMKs. I think he shot good groups initially but decided to try the re-crown to see if it would bring the group size down more. He even threw in a light-weight buffer and spring in the return package.

I can't say enough about M1S's customer service... A+ in my experience.

Which brings me to the REAL REASON I was having accuracy problems with this upper. The free float tube is much shorter than the tube on my .223 varmit upper (22" barrel vs 16" barrel on the .300) and my Caldwell tackdriver rest/bag is 11" long. Anyone figure it out yet?

When shooting my varmit AR and all my other rifles I never had to worry about the barrel contacting the shooting bag. With the short free float tube on the M1S upper I was having random contact with the barrel and the gas block which was throwing my shots all over. I was surprised it made that much difference. However, when I was careful that the bag didn't touch anything but the tube my shots all landed in less than 1" groups with 220 SMKs and 208 AMaxes.

With that said, I've been working on my other .300 upper (adding an adjustable gas block) while the M1S upper was away and I don't want to switch parts over since both uppers now shoot the same. So, if anyone is interested in a decent price on a complete M1S upper let me know via PM.

edit to add: the M1S upper has been sold

Eviltwin
10-13-2008, 07:33 PM
Well glad things worked out for you, even though you ultimately got rid of the particular upper. I've kind of narrowed down the field to either a Model 1 Sales or a J&T, both seem to have great CS reviews but J&T seems to have a little better rep fresh from the factory... at least on 5.56 uppers - no word on .300 So anyone have any experience with J&T/DoubleStar products in the .300x221? Still debating getting the upper now or another lower or two before the election.