View Full Version : Fitting gas block to barrel
Scoots
05-07-2007, 11:20 AM
My AR project rifle is starting to come along, although it's going much more slowly than I'd like.
I just received my low profile adjustable gas block. I measured the bore diameter of the gas block and the diameter of my Oly barrel at the gas port. I either have to open the bore of the gas block .010" or turn down the barrel at the gas port .010" (hmmmm, I just thought of measuring the bore diameter of the old gas block :bangin: ).
Anyway, what did you guys do to ensure a proper fit of gas block to barrel?
Thanks for your help.
320pf
05-07-2007, 03:37 PM
I had to turn my barrel down to 0.750. The JP gas block has a nice snug fit.
320pf
Like 320pf I also turn the barrel down. Great care must be excercised when turning the barrel because a loose fit will haunt you. Most would probably turn to within a couple of thousandths and then hand fit the block.
Scoots
05-07-2007, 05:54 PM
Thanks for the replies and information.
Would it be easier to open up the bore of the block a little at a time & test for fit?
sniperx
05-07-2007, 06:08 PM
No, not really. You will have to have it machined. .010 is too much to try and polish and would take a long time to try to hone it with a wheel cylinder hone.
Much easier to turn the barrel in a lathe.
tp555
05-07-2007, 08:51 PM
You did not mention what size your barrel or gas block is.Go with the standard sizes like .750" ,.875" or .937". for your barrel. Gas blocks can be replaced a lot easier then your barrel. I would machine the gas block for that reason.I also make gas blocks for the ar in stainless. Sometimes they are undersized like .935"
or something.What ever the customer wants.regards.
Scoots
05-07-2007, 10:44 PM
tp555,
My Oly barell measures about .762" at the gas port, the old gas block measures .760", and the new JP gas block measures .750".
I thought it might be easier to hone out the new gas block, but if not, I'll have to find someone to machine my Oly barrel down to .750".
Thanks to everyone for advice.
320pf
05-08-2007, 12:08 AM
On a somewhat related subject.
Does anyone have an idea on how to go about closing off a gas port?
thanks in advance
320pf
tp555
05-08-2007, 08:26 AM
Your barrel is off standard.Oly is a pita about this. I would recommend machining the barrel to .750" which is standard. Then you can use anyone's .750 gas block.You do need the equipment to do it right and the experience.If you can't find someone locally I do this .I do make ar barrels for a living.The shipping back and forth would cost more then the job.Plan B machine the gas block to fit or send the gas block out for machining.Not as expensive for shipping as the barrel.
Plan C get a custom gas block made .I also do this.
For blocking a gas port you have to drill and tap for a set screw without going
through to the bore.A set screw with an allen hex in it.This was one way of testing out gas port holes. By drilling through the set screw different sizes of holes can be tested.You don't want a large hole going into the bore.The smaller the better.This does require equipment a good mill or so.
320pf
05-08-2007, 10:46 AM
tp555
check you PM's
Scoots
05-08-2007, 11:38 PM
I contacted a local gunsmith shop about reducing the diameter of the barrel to .750" at the gas port and threading the end of my barrel for a suppressor. They quoted me $125, plus I'd have to have the barrel refinished, which would be additional.
Is $125 a fair price or am I getting skinned? :eek:
sniperx
05-09-2007, 12:56 AM
Well, I do not know. ..................
...........................:uzi2:
O,K. I wont be so bad. Most shops charge 65-85 to thread a barrel. I know some that charge 25. 35-.......35- to turn the gas block
area if you take the upper apart and supply the barrel only. I it is probably about in line. /So, 85+35=120.
Depending on what all else they do, they may have a machine set up ready to go. In most cases if you run a shop at 65-85
per hour and you have to set up to turn, thread a barrel, then turn the gas block area, yes, you can spend a couple of hours
doing this. If you have a dedicated machine with tools handy and no one else need the machine, You could do it in 45 min
to an hour. Also, you will have to receive it in, note it, make a work order, do it, do the paper work/accounting, box it back up, log on to UPS make a shipment, print the lable, tape it on, carry the box out to shipping. Ya, I think 125 is fair price.
tp555
05-09-2007, 08:43 AM
My comments are, "Bend over no grease". In regards to $125 for the job.Reasonable would be $25 for the threading and $15 for the gas port work.Add shipping.Unless your a mercedes type of person that has to brag about how much it costs.I would charge the above. I do this for a living. I advertise in the gun digest for over 10 years. I have customers that I make barrels for that are well known.I have made over 100 barrels in a caliber over .40 cal for one customer in the ar-15. There are 6 cals 10mm and higher that I have made barrels for. Not trying to tease but I don't want to piss off my good customer that I do business with by mentioning the name. I would charge $125 for making a new barrel if you supplied the blank and reamer (if exotic caliber).
Example, 6.5x221,6.5x222,8mm herrett,.40super you get the idea.regards.
vBulletin® v3.8.4, Copyright ©2000-2016, Jelsoft Enterprises Ltd.